Filtered generated 368 hits.
-
2021:10 Establishment and use of attention values in environmental fatigue assessments
SSM perspective Background As Swedish NPPs reach their original technical design life, re-assessment of the fatigue life of structural components is needed for safe long term operation (LTO). In these re-assessments one must consider that new knowledge has shown that environmental effects on fatigue life must be considered. One common method to verify the fatigue life of structural components...
Content type: Publications -
2021:09 Mechanisms important for material modelling in weld residual stress analysis
SSM perspective Background The prediction of weld residual stresses (WRS) is very complex as many mechanisms and phenomena influence the development of WRS during welding. For accurate prediction, the constitutive material models used are essential and must be able to describe the material response of the weldment constituents. For example, selection of a material model should only depend on...
Content type: Publications -
2021:05 Cladding tube rupture under LOCA: Data and models for rupture opening size
SSM perspective Background The Swedish Radiation Safety Authority (SSM) follows the research on fuel performance closely. One aspect that is currently being studied in several research projects is the risk of release of fragmented fuel into the primary coolant in case of an accident. This risk depends on complex conditions were one is the possibility and size of a rupture of the fuel rod...
Content type: Publications -
2021:04 Calibration of models for cladding tube high-temperature creep and rupture in the FRAPTRAN-QT-1.5 program
SSM perspective Background In Swedish Light Water Reactors (LWR), stress corrosion cracking of reactor components and welds occurs from time to time. As the nuclear power plants are ageing, it is essential to study and further understand the mechanism for environmentally induced sensitization. Natural cracking is a phenomenon that is difficult to predict and very hard to study since it occurs...
Content type: Publications -
2021:03 Updated radiological risk assessment for the “Radon” type surface disposal facility in Chisinau, Moldova
SSM perspective Background Bilateral cooperation between Sweden and the Republic of Moldova in nuclear and radiological safety and security has been ongoing since 2010, focusing on activities aimed at strengthening the institutional capacity of the National Agency for Regulation of Nuclear and Radiological Activities in Moldova (NARNRA) as well as infrastructure development in radioactive...
Content type: Publications -
2021:01 In situ NMR condition monitoring of cable insulations in Nuclear Power Plants
Prof. István Furó, Dr. Payam Pourmand, Dr. Pavel Yushmanov SSM English...
Content type: Publications -
2021:02 On Water Induced Sensitization of Ni (Fe,Cr) alloys towards Stress Corrosion Cracking in LWR Piping from 1st Principles Modelling
SSM perspective Background In Swedish Light Water Reactors (LWR), stress corrosion cracking of reactor components and welds occurs from time to time. As the nuclear power plants are ageing, it is essential to study and further understand the mechanism for environmentally induced sensitization. Natural cracking is a phenomenon that is difficult to predict and very hard to study since it occurs...
Content type: Publications -
2020:16 Estimates ofJ-integral and COD for circumferential through wall cracks under global bending including the effect of pipe end restraint
SSM perspective Background Leak-before-break (LBB) piping assessments have shown that piping systems can withstand long through-wall cracks before pipe rupture is expected. This is somewhat because pipe ends are restrained. In LBB assessments analyses are often performed for a pipe segment uncoupled from the piping system, as pipe ends are assumed unrestrained. This assumption is conservative...
Content type: Publications -
2020:15e Protective Actions in Nuclear or Radiological Emergencies - Planning Basis for Events in Emergency Preparedness Category IV
In this report, the Swedish Radiation Safety Authority (SSM) presents planning basis for protective actions in the event of nuclear or radiological emergencies in connection with activities and acts in emergency preparedness category IV. Activities and acts encompass events in activities with ionizing radiation that are not conducted in a specifically defined location as well as antagonistic...
Content type: Publications -
2020:12 Assessment of the QT-COOL coolant channel module against the PBF RIA 1-2 experiment
SSM perspective Background The fuel rod analysis program SCANAIR has been developed by IRSN (Institut de Radioprotection et de Sûreté Nucléaire) for analysis of reactivity initiated accidents (RIA) in light water reactors. The Swedish Radiation Safety Authority (SSM) has access to SCANAIR in exchange for annual contributions for its further development. This ensures a possibility...
Content type: Publications