Filtered generated 275 hits.
-
2021:10 Establishment and use of attention values in environmental fatigue assessments
SSM perspective Background As Swedish NPPs reach their original technical design life, re-assessment of the fatigue life of structural components is needed for safe long term operation (LTO). In these re-assessments one must consider that new knowledge has shown that environmental effects on fatigue life must be considered. One common method to verify the fatigue life of structural components...
Content type: Publications -
2021:09 Mechanisms important for material modelling in weld residual stress analysis
SSM perspective Background The prediction of weld residual stresses (WRS) is very complex as many mechanisms and phenomena influence the development of WRS during welding. For accurate prediction, the constitutive material models used are essential and must be able to describe the material response of the weldment constituents. For example, selection of a material model should only depend on...
Content type: Publications -
2021:08 Recent Research on EMF and Health Risk, ifteenth report from SSM’s Scientific Council on Electromagnetic Fields, 2020
SSM perspective Background The Swedish Radiation Safety Authority’s (SSM) Scientifc Council on Electromagnetic Fields monitors current research on potential health risks in relation to exposure to electromagnetic fields and provides the authority with advice on assessing possible health risks. The Council gives guidance when the authority must give an opinion on policy matters when scientific...
Content type: Publications -
2021:06 Quality Assurance Review of the Swedish Nuclear Fuel and Waste Management Company’s LOT Experiment (Phase S2 and A3) at the Äspö Facility in Sweden
SSM perspective Background This report presents a quality assurance (QA) review of the work done by SKB to retrieve the S2 and A3 parcels from the Long term test of buffer material (the LOT experiment) at the Äspö Hard Rock Laboratory. Each LOT parcel comprises a heated copper tube surrounded by bentonite, with a number of copper coupons and various other test and monitoring instruments...
Content type: Publications -
2021:05 Cladding tube rupture under LOCA: Data and models for rupture opening size
SSM perspective Background The Swedish Radiation Safety Authority (SSM) follows the research on fuel performance closely. One aspect that is currently being studied in several research projects is the risk of release of fragmented fuel into the primary coolant in case of an accident. This risk depends on complex conditions were one is the possibility and size of a rupture of the fuel rod...
Content type: Publications -
2021:04 Calibration of models for cladding tube high-temperature creep and rupture in the FRAPTRAN-QT-1.5 program
SSM perspective Background In Swedish Light Water Reactors (LWR), stress corrosion cracking of reactor components and welds occurs from time to time. As the nuclear power plants are ageing, it is essential to study and further understand the mechanism for environmentally induced sensitization. Natural cracking is a phenomenon that is difficult to predict and very hard to study since it occurs...
Content type: Publications -
2021:03 Updated radiological risk assessment for the “Radon” type surface disposal facility in Chisinau, Moldova
SSM perspective Background Bilateral cooperation between Sweden and the Republic of Moldova in nuclear and radiological safety and security has been ongoing since 2010, focusing on activities aimed at strengthening the institutional capacity of the National Agency for Regulation of Nuclear and Radiological Activities in Moldova (NARNRA) as well as infrastructure development in radioactive...
Content type: Publications -
2021:02 On Water Induced Sensitization of Ni (Fe,Cr) alloys towards Stress Corrosion Cracking in LWR Piping from 1st Principles Modelling
SSM perspective Background In Swedish Light Water Reactors (LWR), stress corrosion cracking of reactor components and welds occurs from time to time. As the nuclear power plants are ageing, it is essential to study and further understand the mechanism for environmentally induced sensitization. Natural cracking is a phenomenon that is difficult to predict and very hard to study since it occurs...
Content type: Publications -
2021:01 In situ NMR condition monitoring of cable insulations in Nuclear Power Plants
Prof. István Furó, Dr. Payam Pourmand, Dr. Pavel Yushmanov SSM English...
Content type: Publications -
2020:16 Estimates ofJ-integral and COD for circumferential through wall cracks under global bending including the effect of pipe end restraint
SSM perspective Background Leak-before-break (LBB) piping assessments have shown that piping systems can withstand long through-wall cracks before pipe rupture is expected. This is somewhat because pipe ends are restrained. In LBB assessments analyses are often performed for a pipe segment uncoupled from the piping system, as pipe ends are assumed unrestrained. This assumption is conservative...
Content type: Publications